P0141 – Meaning, Causes, Symptoms, & Fixes

Code P0141 Definition

O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) – Downstream

Code P0141 Meaning

Heated oxygen sensors contain heating elements to help them get to operating temperature quickly in order to minimize the amount of time spent before they can provide feedback to the powertrain control module. Sensor two is downstream of the catalytic converter ensures the catalytic converter is operating efficiently by monitoring the air-fuel ratio coming out of the catalytic converter. Code P0141 occurs when the powertrain control module tests the downstream heated oxygen sensor’s heater circuit on Bank 1 and detects a short in the circuit or excessive resistance in the heater circuit.

P0141 Symptoms

  • Check Engine Light is on
  • Engine running rough
  • Decreased fuel economy

P0141 Causes

  • Faulty rear most oxygen sensor
  • Faulty wiring/connections
  • Short or open ground in the wiring

Code P0141 Severity – Low to Moderate    

This Diagnostic Trouble Code (DTC) does not need to be attended to immediately, but this DTC could result in more costly repairs in the future.

Code P0141 Common Diagnosis Mistakes

Replacing the oxygen sensor when the issues could actually lie in the catalytic converter, wiring/connections, or an exhaust leak before the oxygen sensor.

Code P0141 Diagnosis Steps

  • Tools Needed to Diagnose:

How To Diagnose P0141

This video does a great job of outlining the diagnostic process for P0141, but we have provided an overview below:

  1. Do a road test. Clear the fault codes with your FIXD sensor and drive around to verify a failure.
    1. If the Check Engine Light comes back on continue to Step 2
  2. Check that the O2 sensor is getting battery voltage by using your multimeter.
    1. Consult your vehicle repair manual to locate the harness connector for the O2 sensor
    2. Disconnect the harness connector and turn the ignition to the on position (do not crank car)
    3. Test O2 sensor for proper voltage with a multimeter using the instructions from your vehicle’s repair manual.
  3. Visually check the electrical connections, wire harness, and metal tabs in terminals for any damages
    1. Damages found? Replace O2 Sensor – Clear code
    2. No damage? Continue on to Step 4
  4. Check the engine ground – Consult your repair manual to find where the engine ground is located
    1. Corrosion? Loose connections? Remove corrosion/tighten and restart the diagnostic process

* Still having trouble finding the issue with your vehicle? Please take it to the nearest auto shop so that they may check other possible issues including the Engine Control Module (ECM).

Was this post helpful?

Comments 10

Kelly P

August 10, 2018

I get intermittent fuel gauge operation, no dome lights when doors are opened, cleaned o2 sensor plug in connection it was rusty or filled with rust-colored corrosion and the temperature control thermostat is malfunctioning needs to be replaced. Will that cause the rear most o2 sensor to malfunction? Thank you.

Stacy Reazin

October 19, 2018

I think the information is very helpful and at what location is the mechanic in the photo? 😉

Julius Davids

April 19, 2019

Awesome info , this is great

Mike Primacio

June 8, 2019

Very helpful info to detail. Thanks Fixd!!


June 26, 2019

So if my check engine light stays off, after oil change and reset of the service engine, it’s good?


July 20, 2019

Theres mire to it than that layra. You have to drive it for about an hour or two. Look up getting obd emissions readt car


July 19, 2019

When the check engine light remain on what are the cause and how to clear it

actual multiple monitors keygen

August 4, 2019

Thank You for this!


August 6, 2019

My engine keeps on cranking I’ve even changed the crankshaft sensor bt it still cranks,plz help me

William Charles Corall

October 8, 2019

what does it mean bank 1?

en English